Tags that Shake

There are a lot of instructions on how to make shaker boxes, or pieces for cards or tags, out there, so this is just another one to give you some ideas to try.

Here are the two tags that I made:

11-16-15 Shaker Tags 7

Okay, these aren’t the greatest pictures, but the light has just been strange today (both sun and indoor).

Now, I saw some instructions that said to use adhesive craft foam for them.  I didn’t have any adhesive foam, but I did have some craft foam.  So, I used that for the tree.

To start, I cut 2 pieces of card stock and 1 of the foam in the large (2nd size down of the dies) tree size. (Sizzix Christmas Trees)  I cut the smallest tree size out of the center of one of the card stock trees and the foam.  I also cut the size in between out of plastic/acetate.  (I just save the plastic that seems pretty sturdy from boxes, box fronts, die holders, etc.)

11-16-15 Shaker Tag 1

11-16-15 Shaker Tag 2

I saved the two cut out small trees for cards.  Now, like I said, I didn’t have adhesive foam, so I just used some craft glue.  First, I put a bit of glue around the edges of the hole on the back of the front piece and adhered the acetate on it, fairly centered.  Then, I adhered the foam piece to the bottom tree (one without the hole).  I put some confetti (this was actually saved from a card, or something that had a pouch as part of it, from years ago.  I have used this confetti for several projects and have quite a bit left.  Definitely recycle stuff you might use!)  in the center of the foam.

11-16-15 Shaker Tag 3

Then, I smeared some glue around the foam piece and layered the top piece on that, lining up the edges.  For this one, I used a hole punch near the top and ran some ribbon through as a tie.

Now, for my second tag, I did it a little differently.  For this one, I did hearts (Sizzix heart dies).  I cut two of the scalloped hearts out of a dark pink (cranberry) card stock, the smooth edge heart that was almost the same size is what I used for the acetate, and a smaller smooth edge heart for the hole.  Instead of using foam on this one (I only had green foam), I used some foam mounting tape.  The glue was used to adhere the acetate to the back of the front piece.

11-16-15 Shaker Tag 5

On this one, I cut little pieces of the foam mounting tape and outlined the hole as best I could, with no spaces large enough for the confetti to fall out.  It took longer and didn’t wind up as smooth as using the foam.  However, it did work.  The worst part of this tag was, after I put the little heart confetti in the middle, I took off the liner from the foam mounting adhesive.  Definitely not the way to go, as the confetti kept popping out and getting stuck on the adhesive.  Might have worked better to put that in after all the liner was off.  Oh well, live and learn.  I used some of the glue to attach the ribbon on the back piece of this one, moving it so it wouldn’t show.  Then I pressed that back piece on top of the front piece.  Because of the adhesive, you have to line this one up before you actually lay it down and press it together.  (The ability of the glue to slide for a few seconds helped on the first one.)

11-16-15 Shaker Tags 7

Here are the two finished tags.  It really wasn’t too difficult, will make some really fun tags for presents and let me play with paper.  I suggest using a pretty heavy duty card stock for these, to hold it all together well.  The foam was easier, but layer the top card stock and the foam together when cutting the centers out.

I haven’t decorated these, yet, but I probably will add some little ornaments around the edges of the tree one.  You can also decorate the inside with a scene, but I like just being able to see the confetti moving around.  Also, if you get any glue on the acetate where it will show, use an alcohol wipe to clean it up easily.

Thanks for spending some time with me today!

Advertisements

Published by

Golda

I am a child of God, wife, mother, daughter, sister and friend. My favorite things to do are: read, make cards and candles, share what I've learned.

Thanks for leaving a comment!

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s